// // Leave a Comment

Using P-Elements in Ansys


Introduction

This tutorial was completed using ANSYS 7.0. This tutorial outlines the steps necessary for solving a model meshed with p-elements. The p-method manipulates the polynomial level (p-level) of the finite element shape functions which are used to approximate the real solution. Thus, rather than increasing mesh density, the p-level can be increased to give a similar result. By keeping mesh density rather coarse, computational time can be kept to a minimum. This is the greatest advantage of using p-elements over h-elements.
A uniform load will be applied to the right hand side of the geometry shown below. The specimen was modeled as steel with a modulus of elasticity of 200 GPa.

Preprocessing: Defining the Problem


  1. Give example a TitleUtility Menu > File > Change Title ...
    /title, P-Method Meshing
  2. Activate the p-Method Solution OptionsANSYS Main Menu > Preferences
    /PMETH,ONSelect p-Method Struct. as shown below
  3. Open preprocessor menuANSYS Main Menu > Preprocessor
    /PREP7
  4. Define KeypointsPreprocessor > Modeling > Create > Keypoints > In Active CS...
    K,#,x,y,zWe are going to define 12 keypoints for this geometry as given in the following table:
    KeypointCoordinates (x,y,z)
    1(0,0)
    2(0,100)
    3(20,100)
    4(45,52)
    5(55,52)
    6(80,100)
    7(100,100)
    8(100,0)
    9(80,0)
    10(55,48)
    11(45,48)
    12(20,0)
  5. Create AreaPreprocessor > Modeling > Create > Areas > Arbitrary > Through KPs
    A,1,2,3,4,5,6,7,8,9,10,11,12Click each of the keypoints in numerical order to create the area shown below.
  6. Define the Type of Element
  7. Preprocessor > Element Type > Add/Edit/Delete...For this problem we will use the PLANE145 (p-Elements 2D Quad) element. This element has eight nodes with 2 degrees of freedom each (translation along the X and Y axes). It can support a polynomial with maximum order of eight.
    After clicking OK to select the element, click Options... to open the keyoptions window, shown below. Choose Plane stress + TK for Analysis Type.

    Keyopts 1 and 2 can be used to set the starting and maximum p-level for this element type. For now we will leave them as default.
    Other types of p-elements exist in the ANSYS library. These include Solid127 and Solid128 which have electrostatic DOF's, and Plane145, Plane146, Solid147, Solid148 and Shell150 which have structural DOF's. For more information on these elements, go to the Element Library in the help file.

  8. Define Real Constants
  9. Preprocessor > Real Constants... > Add...In the 'Real Constants for PLANE145' window, enter the following geometric properties:
    1. Thickness THK: 10
    This defines an element with a thickness of 10 mm.

  10. Define Element Material PropertiesPreprocessor > Material Props > Material Models > Structural > Linear > Elastic > IsotropicIn the window that appears, enter the following geometric properties for steel:
    1. Young's modulus EX: 200000
    2. Poisson's Ratio PRXY: 0.3
  11. Define Mesh SizePreprocessor > Meshing > Size Cntrls > ManualSize > Areas > All Areas...For this example we will use an element edge length of 5mm.
  12. Mesh the framePreprocessor > Meshing > Mesh > Areas > Free > click 'Pick All'

Solution Phase: Assigning Loads and Solving


  1. Define Analysis Type
  2. Solution > Analysis Type > New Analysis > Static
    ANTYPE,0

  3. Set Solution Controls
  4. Solution > Analysis Type > Sol'n ControlsThe following window will pop up.

    A) Set Time at end of loadstep to 1 and Automatic time stepping to ON
    B) Set Number of substeps to 20, Max no. of substeps to 100, Min no. of substeps to 20.
    C) Set the Frequency to Write every substep

  5. Apply Constraints
  6. Solution > Define Loads > Apply > Structural > Displacement > On LinesFix the left side of the area (ie all DOF constrained)
  7. Apply Loads
  8. Solution > Define Loads > Apply > Pressure > On LinesApply a pressure of -100 N/mm^2

    The applied loads and constraints should now appear as shown in the figure below.

  9. Solve the System
  10. Solution > Solve > Current LS
    SOLVE

Postprocessing: Viewing the Results


  1. Read in the Last Data SetGeneral Postproc > Read Results > Last Set
  2. Plot Equivalent Stress
  3. General Postproc > Plot Results > Contour Plot > Element SoluIn the window that pops up, select Stress > von Mises SEQV

    The following stress distribution should appear.

  4. Plot p-Levels
  5. General Postproc > Plot Results > p-Method > p-LevelsThe following distribution should appear.

    Note how the order of the polynomial increased in the area with the greatest range in stress. This allowed the elements to more accurately model the stress distribution through that area. For more complex geometries, these orders may go as high as 8. As a comparison, a plot of the stress distribution for a normal h-element (PLANE2) model using the same mesh, and one with a mesh 5 times finer are shown below.


    As one can see from the two plots, the mesh density had to be increased by 5 times to get the accuracy that the p-elements delivered. This is the benefit of using p-elements. You can use a mesh that is relatively coarse, thus computational time will be low, and still get reasonable results. However, care should be taken using p-elements as they can sometimes give poor results or take a long time to converge.

0 comments:

Post a Comment